shrink fit
英 [ʃrɪŋk fɪt]
美 [ʃrɪŋk fɪt]
冷缩配合；烧嵌；热配合
双语例句
- The default behavior of Mobile Safari is to assume that the Web site is980 pixels wide and shrink it by about one-third to fit in the viewable area of the iPhone.
MobileSafari的默认行为将假定Web站点的宽度为980像素，并且把它收缩三分之一以适应iPhone的可视区域。 - The simulation model of the wheel is set up and the stress of shrink fit has been analyzed by using ANSYS.
建立轮毂装配的仿真模型，用ANSYS的接触单元对轮毂的过盈装配的应力情况进行了分析。 - As these devices shrink, ordinary batteries won't be small enough to fit inside.
因为这些设备变小了，普通电池就无法安装进去了。 - When we say older people shrink, we don't mean they become tiny enough to fit in your pocket!
当我们说老人变矮，并不是说他们变得小得都可以装进你的口袋！ - Through analyzing finite element in shrink fit, the application of the contact element in shrink fit is discussed.
通过对过盈装配的有限元分析，研究接触单元在过盈连接中的作用。 - Celtic jerseys are not for second best, they don't shrink to fit inferior players.
凯尔特人的球衣从来都是追求最好，它不会为了迎合任何不配这白绿条衫的球员而缩水。 - Were the dress to shrink, would it fit for you?
如果这件衣服缩水，你穿着还合身吗？ - Renovation Calculating& Shrink Fit Process for Hot Continuous Rolling Mill Roll Shifting Mechanism
热连轧窜辊装置改造计算及热装工艺道生热载体供应装置 - The relative sizes of the turn down rims of the fins were determined for the processing characteristics of square finned tubes, the shrink fit technology program of the casing fin tubes was proposed.
针对方形翅片管加工特点，确定了翅片翻边的相关工艺尺寸，提出了套片式翅片管的热套工艺方案。 - Mechanical model study for shrink fit rotor
热套转子力学模型研究 - The test method employed is non-destructive, so that only one model is needed for investigating stresses in a rotating disc at various speeds, and for determining the static shrink fit stresses.
由于这是一种非破坏试验方法，所以仅一个模型就可以对几种不同转速以及静过盈状态下的应力进行测定。 - The laws of Change in Material Strength of Structural Parts and Change in Clearance of Shrink Fit of The Shaft-through for The Explosion-proof Motor used in Low Temperature Ambience
低温防爆电动机结构件材质强度及轴贯通配合间隙冷缩变规律 - Based on the contact simulation, discuss the applications of the general contact elements in the shrink fit in disc and shaft.
通过接触仿真分析，研究接触单元在轮轴过盈联接中的应用。 - The transfer matrix across the shrink fit section is established. This paper puts forward a method for calculating shrink fit to replace the traditional empirical method.
本文导出了热套段模型的传递矩阵表达式。本文给出一种组合活塞配合间隙（过盈）值的计算方法，可以替代以往单凭经验估算的传统方法。 - Finite element analysis of shrink fit in disc with shaft
轮轴过盈联接有限元分析 - Several Problem With the Shrink Fit Between Shaft and Rotor Core of the Large-Sized Motor
大型电机转子铁心热套轴应注意的几个问题 - In the FEA model, the geometric nonlinearity due to large deformation, material nonlinearity, shrink fit between tire and rim and the nonlinearity of tire contact are taken into consideration.
在有限元模型中考虑了轮胎的几何非线性、材料非线性、轮胎与轮辋过盈配合以及轮胎接触非线性。 - The cylindrical surface shrink fit process to match large gears and their axles is practised in the manufacture of large electro blocks HC8 and HC16 now under development.
本文在研制的HC8和HC16大型电动葫芦中，大齿轮与轴之间采用了圆柱面过盈联接。 - This paper puts forward a method for calculating shrink fit to replace the traditional empirical method.
本文给出一种组合活塞配合间隙（过盈）值的计算方法，可以替代以往单凭经验估算的传统方法。 - Touch on replacement of shrink fit in tolerance system by inorganic bonding
论以无机粘接取代过盈配合 - An engine accident by slipping of shrink fit crankshaft which caused severe damage of two main bearings is analyzed.
对主机曲轴红套滑移，并使二道主轴承严重损坏的机损事故进行了分析。 - ? Analyzed the stress distribution under the common act of the environment temperature, inertia force and shrink fit when the rotor was working.
转子工作时，在环境温度、惯性力及过盈配合等多种因素的共同作用下，分析了转子的应力分布。 - This paper introduces in detail the technique of partial replacement and repair to the glide in big angle of the crank shaft at shrink on fit by examples.
通过实例详细介绍了曲轴红套部位大角度滑移的局部更换修理工艺。 - According to the motor shaft-small gear shaft shrink fit, the work which owned hardness test, fracture analysis and crack analysis, had been done to find invalidation mechanism.
针对电机轴-小齿轮轴过盈配合，从硬度测试、断口分析和裂纹分析三个角度入手，确定了其失效模式与失效机理。